Home :: OSD / Telemetry :: DJI Innovations :: Video Cable for Phantom2 with DJI iOSD Mini & Zenmuse (Flysight ~ Boscam ~ Foxtech)
Close
Details to FREE USA Shipping. We specialize in FPV Drone parts. USA domestic orders over $99 can qualify for free ground shipping.
The special Free Shipping applies to orders delivered within the Continental USA, Alaska & Hawaii.
Some restrictions apply. Click HERE for more details.

Video Cable for Phantom2 with DJI iOSD Mini & Zenmuse (Flysight ~ Boscam ~ Foxtech)

Video Cable for Phantom2 with DJI iOSD Mini & Zenmuse (Flysight ~ Boscam ~ Foxtech)
This FPV cable is for Phantom 2 installations that have a Zenmuse H3-2D / H3-3D / H4-3D Gimbal with Hero3/3+, or H3-3D-1.1 Gimbal with Hero3/3+/4. It is used to connect a FPV video transmitter and DJI iOSD Mini to it. The cable is compatible with our 5.8GHz Flysight video transmitter and can be used with most Boscam and Foxtech 5.8GHz video transmitters too. Our cable takes all the guesswork out of connecting the equipment. Best of all, the cable is a plug-in installation (no soldering required).

There are four connectors on the cable. The two black Molex plugs (2-Pin power & 5-Pin Video) go to the Flysight, Boscam, or Foxtech 5.8GHz video transmitter. The white 4-pin plug mates with the DJI iOSD Mini's video port. The white 6-pin plug goes to the P2's central circuit board (inside the plastic shell). Overall length is 11-inches (28cm).


IMPORTANT NOTICE: This cable is specifically designed for directly connecting the Phantom2 (with Zenmuse) and a DJI iOSD Mini to the Flysight 5.8GHz transmitter that we sell. It is also compatible with the 5.8GHz Boscam and Foxtech FPV transmitters that have a 2-Pin battery cable and 5-Pin video cable. This cable is NOT compatible with ANY other hardware configurations and using it with other video transmitters may cause damage that will void your equipment warranties.


Referring to the photo below, a summary of each connector is as follows:

vTX 2-PIN:  Video Transmitter DC IN plug.

vTX 5-PIN: Video Transmitter A/V Plug.

P2: Phantom 2 CAM Port. Connect this white plug into the Phantom2's Central Circuit Board (6-Pin CAM jack). This cable provides video and power connections from the DJI model.

iOSD: White colored 4-pin plug. Connect to the iOSD Mini video port. The iOSD must be connected and correctly operating in order to have a video image. Do NOT omit this plug!

Installing the cable involves disassembly of the DJI Phantom 2 which requires familiarity with working on the model. Please see the information above for basic installation details (no other instructions are provided).

This cable does not provide audio from the GoPro camera. If your transmitter has a built-in microphone then it will continue to operate normally.

Details
SKU #CABP2-FB-OZ28
Ship Wt. 0.03 lbs
 
Our price: $9.99 Item In Stock!
Quantity Price
3-9 Items $9.79
10+ Items $9.49
*Note:
Options
Quantity
Cable Connections
Basic Installation
Cable Installation Hole
Cable Plug Location
Location of P2 connector
DJI Phantom Prop Nut (CW or CCW) Vector / MicroVector Airspeed Expander with Pitot DJI Phantom Rear Mounting Plate
$1.99
$33.99
$9.95
 
Vector / MicroVector Current Sensor (PSU) with XT60 Connectors Power Cord, Dual 2.1mm Barrel Plugs to XT60 Male A/V Pigtail Cable for TX9-500 / TX13-300 / TX13-1000Transmitters
$33.99
$6.49
$3.99
 
Power Cord, 2.1mm Barrel Plug to JST BEC Female DJI Phantom 2 FPV Cable & Hub Video Cable for Vector / Fatshark or ImmersionRC vTx / FatShark Camera
$3.99
$9.79
$8.49

Payment Logos Bitcoins accepted here